I will certainly cover the necessary steps for each and every sort of flooring.
* Bona brand "Prep" or Basic Coatings brand "Tycote" (these are etching solutions that help ensure a new layer will bond in order to your floors - note: only wanted for pre finished solid or pre finished engineered floors)
* A solid wood floor finish that will is compatible together with the etch merchandise; for anyone who is getting typically the Bona product I'd recommend Bona Site visitors HD finish or perhaps Bona Woodline finish, or in the event you find the Basic Linings Tycote, I'd suggest their Street Sneaker Finish.
* Floors Buffer - You can rent a ground buffer at almost any tool rental store including some home improvement stores. If you've never ran a normal buffer an individual may consider obtaining a square buffer as these vibrate rather compared to oscillate.
* Hoover - I suggest one having a smooth bristle or gentle felt brush.
5. MicroFiber Dust Cleaner
* Applicator - I recommend a good 18" t-bar design application made by simply Duratool.https://thewindowexperts.ca/service-areas/replacement-windows-doors-georgina/ , and smaller quick sleep paint rollers can also work for this.
* Brush - I prefer the foam fashion 3-4" wide tooth brushes.
* Buffer Protect - White Patches (1-2) also obtainable at tool local rental store (additional red or maroon pad in case you have pre completed engineered or pre finished solid floors)
* Sanding Display 150 or two hundred and twenty grit - These kinds of are also available in tool rental retailers or online. An alternative to these kinds of are Norton brand sand dollars buffer pads.
Prepare
Typically the first thing likely to want to do is prep the room you are performing. You'll want in order to remove all furniture and any other items that are recorded the floors you are carrying out. It's also a good idea to be able to use some painters tape to tape out of the baseboards, and to tape away adjoining surfaces/floors that you want to protect. An individual may also want to say goodbye a few plastic film in doorways to assist contain the dust produced. You'll also want to brush your flooring surfaces and make certain there are no pieces of debris as these things could easily get caught under typically the buffer and scratch the floors.
Polishing
After prepping typically the space now you must to be able to buff the flooring. Take the white-colored buffer pad and set in on typically the bottom with the terme conseill drive head. Next put the sanding screen under the white pad (the screen is what you want in order to be touching the particular floor). Now commence the buffer and moving in some sort of back and forth motion buff more than the floors looking to go with the particular grain of typically the wood. Try to cover up every inch involving the floors very well.
After buffing typically the floors now an individual want to take an used item of the sanding screen and gently hand sand in areas of the floor that the load wouldn't reach like corners, under cupboards, under radiators etc . This is just to also etch the surface of these areas too.
The next thing will vary a new bit using the type of flooring you could have.
If you have pre finished floors, the next factor you should do is to aficionado the floors once again. On this occasion you would like to use just the red or maroon buffer pad. So what now you're going in order to do is a wet or damp buffing. You want to mist some regarding the Bona Prepare of Basic Films Tycote onto the floor using a spray bottle. This phase is to etch the surface involving the floors and ensure that a new coating will certainly bond for the finish that is for the factory finished floor product. You'll need to do that quite well to make sure you get each inch in the floors and that just about every inch has a great etched or uninteresting kind of look to it. You'll actually want to take some the load pad and find into the edges and other limited spots that the buffer wouldn't reach.
(note: you can use this step on solid wood floors that were site finished too, specifically if you have any kind of doubts about a new coating keeping to the present finish you have or if you have utilized any wax structured cleaners or rejuvenating products which can be wax tart based since they can prevent new films from staying with the particular floors)
Cleanup
Following you complete typically the buffing part associated with the project, right now you want to clean your floors really well. You'll want to vacuum cleaner the floors really well and next dust mop all of them very well.
Coating
As soon as you have cleaned out the floors, today you're ready to apply the coating(s). The actual manufactures guidelines for that amount associated with square feet involving coverage per gallon. Apply the end with all the grain making use of whatever type regarding application you chosen up. Be certain to work in sections.
Let Dried
After you have utilized the coating at this point you'll just desire to wait the recommended dry time before walking upon the floors. A person can find this kind of on the end container. Then you'll want to wait around the manufacturers suggested time for curing ahead of putting furniture again into place.
Duplicate if Ideal
When you'd like an individual can also buff the floor again and apply some sort of 2nd, or 3rd coating for additional protection. I like to recommend polishing after each covering with a 230 grit sanding monitor and following all the other instructions aside through using the etching items because they will certainly not be needed as soon as one coating is definitely applied.
